Autometer Gauges CNC Brakes EMPI Douglas Wheel Technology Fox Shocks Jamar Performance k4 Switches



Usa Made Irs Rear Chromoly 3 Inch Longer 3 Inch Wider Trailing Arms With Beetle Bearing Housings

Usa Made Irs Rear Chromoly 3 Inch Longer 3 Inch Wider Trailing Arms With Beetle Bearing Housings
    Country Of Origin: USA
    Quantity in Basket: None
    Part Number: ac530015cmus
    Price: $924.00
    Sold As: 1 Driver Side And 1 Passenger Side Rear Trailing Arm

     
    Quantity:
     
    This set of rear 3 x 3 IRS rear trailing arms uses standard 1969 to 1979 beetle stub axles, bearings, seals, and spacers. These arms can also be used with beetle to bus or beetle to Porsche 930 ADAPTER stub axles. The arms do not have shock mounts welded to them allowing you to position the shock where ever is necessary for your sand rail, baja bug, or manx.

    The term 3 by 3 refers to the amount of inches wider and longer than a stock beetle trailing arm. On this particular set of arms they are 3 inches wider per side and 3 inches further towards the rear of the vehicle. If you have a beetle transmission you should need a 20.25 inch long axle. If you have a bus transmission you should need a 19.25 inch long axle. However, axle length could change based on your wheel alignment toe in or toe out and also where you have your transmission mounted in relation to the trailing arms. It is important to check your own axle length BEFORE you mount the axles on the vehicle.

    How To Measure An IRS Axle Length
    How to Measure IRS Axle Length:

    1.) First adjust your rear wheel alignment toe in. If your tires are toed out like a duck your trailing arms will be closer to your transmission resulting in a shorter axle.

    2.) Lift the trailing arm so that if you did have an axle it would be parallel to the floor at zero degrees. This is your shortest point.

    3.) Measure from the center of the drive flange on your transmission to the center of the stub axle on your trailing arm. DO NOT measure where your CV joint mounting surface is. You need to measure the bottom of each cup because this is where your axle will plunge into. If you purchase too long of an axle, when your trailing arm moves upward to zero degrees it will shove the axle into the transmission. This will mushroom the ends of your axles and eventually crush the ring gear inside your transmission.

    4.) After you have measured this distance, you subtract 1/4 inch total length. For instance if you measure from the center of the drive flange to the center of the stub axle and you get 20 1/2 inches you would buy a 20 1/4 axle.

    5.) Measure both sides of the car. It is VERY common to have unequal length axles.



    1. Inner Spacer: Face the inner bevel of the inner spacer towards the bottom of the stub axle.

    2. Inner Bearing: The inner bearing is the "ball bearing". This bearing does not have a removable inner race.

    3. Center Spacer: Long spacer goes in the middle, the direction does not matter.

    4. Outer Bearing: The outer bearing is the "roller bearing". This bearing has the removable inner race.

    5. Outer Spacer: This is very important! Face the outer beveled edge of this spacer towards the outer bearing.



    Related Parts
    Part Number Name Image Price  
    ac598990b Bearing And Seal Kit For Both Rear Irs Trailing Arms Bearing And Seal Kit For Both Rear Irs Trailing Arms
    $76.75
    ac598990c Complete Bearing, Seal, Spacer, Cap, And Snap Ring Kit For Both Rear Irs Trailing Arms Complete Bearing, Seal, Spacer, Cap, And Snap Ring Kit For Both Rear Irs Trailing Arms
    $194.25



    Customers who purchased this product, also purchased:
    Part Number Name Image Price 
    ac530020d Usa Made Delrin Irs Rear Trailing Arm Bushings For Stock Or Aftermarket Arms On Stock Pivot Point Usa Made Delrin Irs Rear Trailing Arm Bushings For Stock Or Aftermarket Arms On Stock Pivot Point $72.00
    ac530020 Urethane Irs Rear Trailing Arm Bushings For Stock Or Aftermarket Arms On Stock Pivot Urethane Irs Rear Trailing Arm Bushings For Stock Or Aftermarket Arms On Stock Pivot $29.00
    ac750720 Weld On Single Shock Mounting Bracket 3/16 Thick Steel With 1/2 Id Hole Weld On Single Shock Mounting Bracket 3/16 Thick Steel With 1/2 Id Hole $6.50
    ac750721 Weld On Dual Shock Mounting Bracket 3/16 Thick Steel With 1/2 Id Holes - Holes Are 4.5 Apart Weld On Dual Shock Mounting Bracket 3/16 Thick Steel With 1/2 Id Holes - Holes Are 4.5 Apart $8.50
    ra18901 Usa Made C1045 Heavy Duty Steel Adjustable Clevis For One Limiting Straps With 1/2 Inch Shank Usa Made C1045 Heavy Duty Steel Adjustable Clevis For One Limiting Straps With 1/2 Inch Shank $23.75
    ac501361k Irs Spring Plate Conversion Kit For Stock Vw Torsion Housing For Coil Over Shocks Or Air Bags Irs Spring Plate Conversion Kit For Stock Vw Torsion Housing For Coil Over Shocks Or Air Bags $201.00
    ac413055-625hd Usa Made Heat Treated Alloy Racing Heavy Duty 5/8 Link Pin Set For Aftermarket Front Trailing Arms Usa Made Heat Treated Alloy Racing Heavy Duty 5/8 Link Pin Set For Aftermarket Front Trailing Arms $146.00
    ac401034-500w Thru Rod Teflon Washer With 1/2 Inch Id Hole To Go Between Thru Rod Nut And Front Trailing Arm Thru Rod Teflon Washer With 1/2 Inch Id Hole To Go Between Thru Rod Nut And Front Trailing Arm $3.25



    Pacific Customs Wholesale Program

    Pacific Customs Shopping Cart
    Your shopping cart is empty.

     

    New Products
    Type 1 Clutch Kit, Early Model Pressure Plate, Metal Woven Disc, Early Throwout Bearing And Alignmen
    Type 1 Clutch Kit, Early Model Pressure Plate, Metal Woven Disc, Early Throwout Bearing And Alignmen
    Price: $169.00
    1958-1964 VW Bug Stainless Steel Brake Hose Kit
    1958-1964 VW Bug Stainless Steel Brake Hose Kit
    Price: $95.00
    Pacific Customs Front King And Link Pin Trailing Arms 4 Inch Longer 1.875 Wider For Coil Over Shocks
    Pacific Customs Front King And Link Pin Trailing Arms 4 Inch Longer 1.875 Wider For Coil Over Shocks
    Price: $695.00
    VW IRS 3x3 Aircraft 4130 Chromoly Tig Welded Boxed Micro Stub Trailing Arms, Made In USA
    VW IRS 3x3 Aircraft 4130 Chromoly Tig Welded Boxed Micro Stub Trailing Arms, Made In USA
    Price: $895.00
    Multi-currencies display